Many housewives are faced with a situation where a washing machine that has been in service for some time beeps when washing. The squeaking sound is heard throughout the entire process, or during rinsing and spinning mode. The most likely reason is wear of parts and loose fasteners. If you do not have the ability or skill to repair the device yourself, then you should contact a specialist.
The most likely causes of squeaking
Modern washing machines Some brands are equipped with devices that notify with a sound that the wash is complete. This feature should be indicated in the instructions for the machine. If the squeak is not a warning sound, then the reasons should be sought in the wear and tear of the household device.
The squeak is a consequence of:
- loosening the belt driving the drum;
- violation of counterweight stability;
- getting stuck small objects and items of clothing;
- rust formation on bearings;
- loosening of the shaft fastenings;
- high degree of spring wear;
- friction of body parts against each other at the joints.
Let's take a closer look at why the washing machine beeps.
Loosening the belt
If old typewriter, without direct drive, then it is most likely that the belt that makes the drum move has become loose. The stretched belt slips, emitting a pronounced squeak.Moreover, the sound is heard when the washing is in active mode, the machine is filled with a large number of things.
To check whether the belt is really to blame for the sound, you need to get to it:
- remove the back cover, behind which the wheel - pulley is located;
- see if there is damage to the pulley;
- inspect the drive belt put on the wheel.
The belt should be inspected carefully. Even a small crack can negatively affect the performance of the part and cause an unpleasant squeak. If damage is found, the belt must be replaced. But sometimes it is enough to increase the tension of the drive part.
Counterweight instability
By removing the cover of the machine, you can see the counterweight. It looks like a massive gray block. The part requires replacement if the diameter of the fastening holes has become wider than the diameter of the fastening bolts. To make sure that the structure is shaky, just shake it in different directions. If the counterweight is wobbly, it's time to replace it.
Hitting objects
When loading clothes into the washing mashine, housewives often forget to check the pockets for small items and coins. During washing, this little thing spills out and penetrates through the hole in the cuff into the space between the drum and the tank. In wash mode the surface of the drum rubs against objects, making squeaks and squeaks.
To check whether small items are stuck inside, you need to unscrew the wall of the washing machine (back or front, determined by the model of the device), and unfasten the heating element. Through the hole for the heater you can see the objects inside and remove them.
Rust on bearings
If the drum beeps during washing mode, the problem may be serious and require professional repair. The drum is attached to a shaft, which is inserted into the tank on bearings.The bearings are protected from moisture penetration by an oil seal. This rubber device gradually dries out and defects appear on it. A damaged seal allows water to pass through. As a result, the bearings become covered with rust and begin to creak and squeak during operation.
If the squeaking sound of the washing machine is a consequence of rusting of the bearings, then washing should be stopped immediately. If damaged bearings continue to operate as before, they will completely break down. And this will certainly lead to the breakdown of other elements, and the washing mashine will have to be scrapped. The only option to do in this situation is to contact a workshop.
Weak shaft fastenings
The problem is not often diagnosed, but it does happen. Gradually, if the washing machine operates in active mode, the shaft fastenings become loose and weakened. The problem can also be a consequence of a manufacturing defect. The result is an imbalance of the drum, the appearance of a characteristic squeak. The problem is easily fixed: you just need to tighten the bolts. But getting to them is problematic; it is better to entrust this matter to a professional.
Spring wear
When your washing machine beeps loudly during the spin cycle, the problem may be worn springs. When the device is working, the tank shakes and the springs rub at the attachment point, producing an unpleasant thin sound.
To confirm the cause of the sound, you need to turn on the washing mode by removing the cover of the machine. Then press on the springs. If the beeping stops, then the problem has been correctly identified. Usually, to eliminate it, it is enough to apply lubricant to the places where the springs are attached. But sometimes it is necessary to replace elements that have become unusable.
Friction of body parts
The fastening elements of the body gradually weaken, and the moving parts begin to squeak and grind when rubbing against each other. The sound is not only characteristic of worn-out devices; it can be the result of a manufacturing defect. You should carefully inspect the washing mashine and tighten any loose fasteners.
If, after a thorough check, the cause of the squeak cannot be identified, you will have to contact a qualified technician to carry out diagnostics and repairs.
The Atlant machine beeps
Owners of the Atlant washing machine (series 50C82) have nothing to worry about: the device beeps, but the reason is not related to a breakdown. An unpleasant sound is a consequence of the operation of the display units and mode switching.
The explanation is as follows: the display unit functions in conjunction with the program selector, which in a washing mashine of this brand is not particularly reliable, and as a result of operation it begins to squeak.
Because of washing machine Atlant beeps, it doesn't work any worse. Occasionally the image on the display gets confused: instead of the selected mode, another one is shown. The message SEL may appear, indicating that the selector is operating incorrectly.
The annoying sound can be eliminated simply by replacing the display module. But after some time the problem may return.
The Atlant 50u107 washing machine beeped during washing 3 times, but there were no other defects. It was cured by unplugging it at night! That's how it happens.