Indesit wisl 82 washing machine operating instructions in Russian

Before you start using a new washing machine, you must carefully read the instructions for it. It describes safety rules, washing modes and other information that will be useful to the new owner of the equipment. This article describes the operating instructions for the Indesit WISL 82 washing machine.

Correct installation of equipment

First, you need to open the packaging of the delivered washing machine. Do this as carefully as possible, because the machine may be faulty. In this case, you will have to pack the unit back.

Then you need to do the following:

1. Carefully inspect the machine body . There should be no mechanical damage. Then you need to open the hatch of the device and inspect the cuff. You also need to check the tray with cells for powder.
2. Inspect the control panel. Check the integrity of the buttons and the regulator for selecting the desired washing program. If damage is detected, immediately notify the seller.
3. Unscrew and remove the transport bolts , located on the back of the machine body. There are four of them. The holes from the bolts must be plugged with special plugs.

Repair

Wash

1. Exploitation
2. Dishwashers
3. Purchase

Miscellaneous

Reviews

1. Home page
2. Exploitation
3. Indesit wisl 82 washing machine operating instructions in Russian
4. CONTENT
5. Correct installation of equipment
6. Adding detergents

Selecting a washing program

Starting the wash

Unit care

Before you start using your new washing machine, you must carefully read the instructions for it. It describes safety rules, washing modes and other information that will be useful to the new owner of the equipment. This article describes the operating instructions for the Indesit WISL 82 washing machine.

1. Correct installation of equipment
2. First, you need to open the packaging of the delivered washing equipment. This must be done as carefully as possible, because the machine may be faulty. In this case, you will have to pack the unit back.
3. Then you need to do the following:
4. Carefully inspect the body of the machine

There should be no mechanical damage. Then you need to open the hatch of the device and inspect the cuff. It is also necessary to check the tray with powder cells.

Check the integrity of the buttons and the regulator for selecting the desired washing program. If damage is discovered, notify the seller immediately.

Unscrew and remove the transport bolts

located on the rear side of the machine body. There are four of them in total. The bolt holes must be plugged with special plugs.

The transport fasteners must be retained. Most likely, they will come in handy in the future when transporting the washing machine.

• Next, you need to decide on the place where the machine will stand. When choosing a location, it is important to consider the following rules:
• The machine must be installed on a solid base. Before installing the device, it is necessary to strengthen the floor. The distance between the walls of the case and other interior items must be at least one centimeter.
• The connection points to utilities (electricity, sewerage, water supply) must be located next to the machine. Preferably, at a distance of 100-150 centimeters. After preparing the place, you can install the washing machine. If you have difficulties connecting the device, you must contact professionals.
• Next, you need to perform the first launch of the "home assistant". But this must be done strictly according to the instructions. During the first launch, the internal parts of the device are cleaned of factory debris and residues of machine oil that got inside the machine during assembly. This is done as follows:
• Open the tray with cells for detergent. Pour a small amount of washing powder into the middle compartment.
• Close the powder receptacle. Select one of the long programs at a water temperature of 90 ° C. This is done using the program selection switch.
• The drum of the machine must be empty. Wait until the washing process is complete.
• After the above steps, you can wash things in the machine. Add detergents
• In order for the quality of washing to be high, it is necessary not only to be able to dose the detergents used. It is also important to learn how to distribute them between the compartments of the powder receptacle. The detergent tray contains four compartments: three of them are main, and one additional, installed if necessary.
• The first cell, located on the left, is used for pre-washing.You only need to add powder to it when the selected program includes pre-wash. The compartment located in the middle is used for the main wash. You need to pour or add detergent there in any case.
• The section on the right is for conditioner and other similar additives.. The additional cell is mounted directly into the first compartment. It is intended for bleach.

When starting the prewash, the fourth compartment must be removed. You only need to insert an additional cell when you start bleaching things. The bleach is poured into a small jar located in the middle of the cell. Then you need to close the tray with the powder cells and start the program.

Selecting a washing program

By reading the operating instructions for this model, you can find a description of the options and programs that the equipment supports.

• When choosing a program, you should take into account a number of parameters, such as the degree of soiling, the fabric from which the items being washed are made, etc. Let's look at the washing programs in more detail.
• Washing programs Indesit WISL 82
• The first mode is “Cotton”.
• Performed at 90°C. Designed for washing heavily soiled white cotton laundry. The program includes a preliminary and main wash, rinsing and spinning. You need to add not only powder to the powder receptacle, but also conditioner. Execution timer: 137 minutes.
• 2nd mode “Cotton”.
• Like the previous one, it is performed at a water temperature of ninety degrees. This program does not have a prewash, but does have the option of bleaching. Completes in 120 minutes.

3rd mode “Cotton”.

Heating water to – 60°C. It is used more often, as it allows you to wash mixed or white cotton linen. This mode is used for washing moderately and heavily soiled items with a strong color. The program contains the main wash, rinsing and spinning. Whitening is also possible. The execution timer is 105 minutes.

4th program “Cotton”.

Water heating during washing is 40°C. It differs from the previous program only in water temperature. This difference is significant. After all, it allows you to wash even lightly soiled colored items that are susceptible to fading in this mode. Running time is 72 minutes.

Water heating - 30 degrees. It is a complete analogue of the previous mode. The only difference is in the water temperature, which affects the quality of laundry washing. Using this program, it is recommended to wash only those colored items that tend to fade a lot. The duration of the regime is 65 minutes.