Electrolux washing machines, like equipment from other manufacturers, break down over time. In this case, the device displays a special code or reports the type of failure by flashing the indicators in a certain sequence. After decrypting the message, the user can contact the service center or try to replace the faulty parts themselves. To do this, he needs to know how to disassemble an Electrolux washing machine.
Washing machine malfunctions
The most common malfunctions of Electrolux washing machines are:
- Water heating does not work.
- The Electrolux machine does not fill with water.
- The drain does not function.
- The rinse program does not run.
- Spin does not work.
- No powder is collected.
- The equipment does not turn on.
- Knocks out the machine gun.
These are the most common faults; in fact, there are many more of them. To solve some of them, for example, to replace a pressure switch, only partial disassembly of the device is necessary. Others will require more serious work to eliminate. So, to replace the bearings, in addition to the housing, it is necessary to disassemble the tank.
Preparing to disassemble the washing machine
To disassemble the Electrolux washing machine, you need to prepare the tools, and then disconnect the equipment from communications and electricity and move it to free space for more convenient work.
When disassembling, you should record every action on camera, especially removing the wiring. This will help you avoid making mistakes during assembly and prevent more serious equipment breakdowns that require expensive repairs.
If you need to purchase new parts, it is better to stay with original or similar ones, but not inferior in quality. The selection and purchase of parts should be carried out strictly in accordance with the model and brand of the Electrolux washing machine.
Disassembling the washing machine
The peculiarity of the Electrolux washing machine is that its body is assembled from two halves: front and rear, connected by screws under the top cover. To carry out repairs, in most cases it is enough to remove the rear part of the case.
The disassembly process is as follows:
- Unscrew the two screws, slide and remove the top protective cover.
- On the left side, you need to unscrew the two screws holding the back panel.
- Repeat on the right side.
- At the back of the bottom of the Electrolux machine there are two more screws that need to be removed.
- The next two screws are on the sides, they are covered with plugs. It is necessary to remove the latter and unscrew the fasteners.
- Now the panel is fixed only by a plastic holder secured with two latches. It is necessary to unclench them and lift the holder. In some models it consists of two halves connected by a screw. You need to unscrew the fasteners, release the latches and remove the holder.
- You can now remove the back panel of the washing machine.
After completing these steps, the user can begin to repair and replace components such as the tank, motor, shock absorbers, pump and pump, belt, drain hose, heating element, etc.
Removing the front panel is necessary to replace the bearings. The following steps must be followed:
- Pull out the detergent tray and unscrew the screws underneath it.
- Remove the control panel. It is held on by latches; you need to act very carefully so as not to damage them.
- You need to disconnect the wiring with caution and after photographing the connection in order to avoid errors during assembly.
- Open the hatch, pry and remove the clamp, tuck the cuff inside the drum.
- Remove the wiring and hose from the pressure switch, remove the fasteners, and disconnect the part.
- Remove the drive belt.
- Disconnect the wiring from the engine, remove the screws, and pull out the motor.
- Pull out the heating element by unscrewing the fasteners and disconnecting the wiring.
- Disconnect the drain pipe and then the hose, having first loosened the clamps.
- Remove counterweights.
- Remove shock absorbers.
- Remove the tank from the springs and pull it out of the machine body.
To replace the bearings you need to disassemble the tank. To do this, unscrew the bolt and remove the pulley. After this, the fasteners securing the tank halves are removed. After the tank is disassembled, the drum is pulled out and work is done to replace the bearings.
If the tank in the Electrolux washing machine is non-separable, it is cut with a hacksaw. Bolts are used to connect the halves back together. Before cutting, fasteners are selected and holes are drilled according to their diameter along the connecting seam of the tank.
How to disassemble an Electrolux vertical washing machine
Disassembly of vertical washing machines occurs as follows:
- Use a slotted screwdriver to pry up the control panel, pull it up and slide it back.
- Tilt it a little, take a photo of the wire connection, disconnect them, and move the panel to the side.
- Disconnect the remaining wires from the electronic board, unscrew the fasteners, and remove the board.
- Remove the fill valve by first disconnecting the hoses from the clamps and disconnecting the wires.
- Unscrew the fasteners and remove the side panels.
- The fasteners holding the front panel in place are now visible. You need to unscrew it, remove the cover and put it aside.
Now the user has access to all important components of the washing machine, including bearings. There is no need to disassemble the Electrolux vertical tank to troubleshoot the problem.
Conclusion
If the Electrolux washing machine breaks down, it will indicate which part is faulty by flashing indicators or a special code on the display. To fix the breakdown, you can call representatives of the service center, but if you know the correct procedure, you can disassemble the washing mashine and carry out the repair yourself. To replace some elements, partial disassembly is sufficient, while for others you will need to completely disassemble the Electrolux machine. The necessary parts can be purchased at a specialized store or service center by telling the seller the brand and model of the washing machine.
