Any washing machines, including those produced by Gorenje, break down over time. To facilitate troubleshooting, a self-diagnosis system is built into modern technology. In the event of a breakdown, the device displays an error code or, if there is no screen, blinks the indicators in a certain sequence. To decipher the message and find out what caused the breakdown, you need to know the error codes of Gorenje washing machines. The difficulty for devices from this manufacturer is that due to a change in the platform, Gorenje equipment is divided into two categories, and the error codes for each of them are different.
Codes for Gorenje washing machines with control system PG1-PG5
- F This error indicates a problem with the temperature sensor. As a rule, the part itself breaks very rarely; usually the wiring from the temperature sensor to the heating element or system board breaks, or a short circuit occurs in the electronic circuit. As a rule, in this situation the program reaches the water heating stage and ends. To diagnose components, you should use a multimeter and test the sensors and circuit. If a problem is identified, it is necessary to repair the broken circuit or replace the broken part with a new one.
- F The door lock does not work.The Gorenje washing machine does not receive a signal from the UBL, so it stops performing the selected mode. In the simplest case, the door is not tightly closed, you need to slam it tightly again and press "Start". If the error appears again, you need to check the electronic lock, the wiring going from it to the system module, inspect the locking lever, i.e. diagnose all components related to the hatch lock.
- F The Gorenje machine made two attempts for four minutes, but did not fill with water. Most often, the problem is caused by low pressure, a clogged or broken water inlet valve, much less often - a broken pressure switch or a clogged tube.
- F For a Gorenje washing machine with a PG1-PG3 control type, this code signals that the system board does not receive a notification from the tachogenerator and stops the drive motor. The equipment tries to start the motor three times, with pauses equal to one minute. If the error is no longer displayed, the wash continues. Otherwise, the selected program is interrupted. If the water temperature in the tank is above 60 degrees, cold water is poured in for a minute. Then, about two minutes, the drain is performed and an error with a fault code is displayed. To eliminate it, you need to check the tachogenerator. For a Gorenje machine with a PG4-PG5 control system, error F4 indicates that the engine cannot spin the drum to the speed set in the program. The attempt is also repeated three times, after which the drain is performed. You need to check the engine board, the condition of the motor, and perform a circuit test.
- Error F5 may also differ for Gorenje machines with different control options.For the PG1-PG3 type, it indicates a malfunction of the triac, which is often associated with overheating of the motor or a malfunction of the triac or motor. For equipment with the PG4-PG5 system, this error indicates the absence of a signal from the motor to the control board. It is necessary to inspect the motor and the system board.
- F This error indicates the absence of water heating or incomplete heating. The problem may be with the heating element or its contacts, the temperature sensor, the heating element relay, in rare cases - with the pressure switch or the system board.
- F The Gorenje washing machine does not drain. It is necessary to inspect and thoroughly clean the drain hose, pump, branch pipe, and also the drain pump. Sometimes the pressure switch or the control board can be broken.
- F This error signals that when spinning, the drum moves at a slower speed than is programmed. It does not appear during the normal operation of the Gorenje washing machine, it can only be detected during a diagnostic check. In this case, it will appear on the screen at the end of the mode. The faulty part in this situation is usually the engine or the electronic board. For a machine with the PG4 and PG5 control type, this means a broken inverter. For all types of washing machines, the problem is sometimes associated with a loose drive belt.
- F This error is typical for Gorenje machines with AquaStop leak protection. If liquid is detected in the machine tray, the leak sensor is triggered and ends the program. The heating element will immediately stop working and the water will be drained.
Codes for Gorenje washing machines with the WA 101, 121, 132, 162, 162P control type
Error codes for SMA Combustion with control type WA 101-162P are significantly different from those described above, but there are also similarities.
- F This error means the temperature sensor is broken. Usually there is a wire break or a short circuit in the circuit. The temperature sensor itself breaks down much less often.
- F The Gorenje washing machine does not fill with water for four minutes and then tries to fill again. If the required amount of liquid is not collected, an error will be displayed on the display. To further execute the specified mode, you need to click “Start”. If the machine does not take water this time, it stops working. It is necessary to inspect and thoroughly clean the filter and hose, diagnose the fill valve and install another part, as well as inspect and, if a breakdown is detected, install a new pressure switch.
- F The control unit does not receive data from the tachogenerator. It is necessary to check the assembly and contacts of the chain, and if a defect is detected, replace the part or restore the chain.
- F Failure of the triac that controls the operation of the motor. To solve the problem, you need to repair the system board.
- F The heating element does not heat the water to the temperature specified by the program. This is due to the heating element itself or the system board. The mode does not end, the error appears on the screen after the wash is completed.
- F The water in the tank is heated to the maximum temperature, regardless of the selected program. As a rule, such an error is caused by a breakdown of the heating element or temperature sensor.
- F This error is caused by a high rate of water heating - faster than what is programmed. The problem may be a pressure switch (low fluid level due to its breakdown), a system board error, or a leak.
- F This error appears if difficulties are detected with draining the liquid. From the moment the process begins, the water should be completely drained from the tank after two minutes. Otherwise, the task is performed again. If another error occurs, F5 is displayed. This can happen if the pump is broken, clogged, or not receiving power. The problem may also be a clogged drain system or problems with the operation of the pressure switch (broken wires, damaged contacts, clogged tube).
- F This error can only appear when running a service check. It means that during the spin cycle the drum rotates more slowly than necessary. The message indicates an engine malfunction. This happens if the drive belt has fallen off, the drum is difficult to rotate, or there is a problem with the motor or system board.
- F The motor control unit cannot transmit a signal to the main module. This means that the circuit leading to the central unit is broken or burned out. You will need to ring and restore the faulty link.
Conclusion
Modern Gorenye washing machines are equipped with a self-diagnosis function that helps detect a breakdown and notify the owner of the device about it. A code is displayed on the screen; to decipher it, you need to know the Gorenje error codes. The difficulty lies in the fact that washing machines produced by this company are based on two different platforms and the error codes for them are completely different. Therefore, in order to correctly decipher the value on the screen, you need to find out the type of control system and refer to the corresponding list of errors.Having deciphered the fault, the washing mashine owner will understand whether the fault can be fixed on his own or whether he should contact the Gorenje service center and call a specialist.
