How to troubleshoot Atlant washing machines

Atlant washing machines have an attractive design and modern technical characteristics, but cannot boast of reliability and service life. Therefore, the issue of repairing the Atlant washing machine becomes relevant for owners over time. In the event of a serious breakdown, it is better to give the unit to a specialist, but the owner can handle some common problems with his own hands.

List of the most typical problems arising with Atlant washing machines:

• The machine does not turn on.
• The drum does not fill with water.
• The drum fills with water too slowly.
• The water does not heat up, the heating element is broken.
• Self-stopping of the washing machine during the cycle.
• The drum does not rotate.
• Problems with draining water.
• Loud or unusual noise during wash or spin cycle.
• Strong vibration, spontaneous movement of the unit on the floor.

• The washing machine door does not open.

Let's look at the causes of breakdowns and options for eliminating them in more detail.

Washing machine won't turn on

If the display does not light up when you press the power button, make sure the power cord is plugged in and there is electricity in the house. If the problem is in the washing machine itself, then the troubleshooting options and methods for eliminating them are as follows:

• Plug fault. Disassemble the plug and check the contact connections.
• Broken power cord. You need to ring the cord.
• There is a fault in the electrical wiring in the washing mashine. Remove the outer panel of the unit and check the condition of the terminal clamps, they may be oxidized.

If the display of the machine automatically reacts to turning on, the washing program is selected, and the machine does not work, the reason is as follows:

• Wrong washing mode selected.
• The door is not closed tightly enough. Check the integrity of the door seal and whether the item being washed has gotten between the door and the body.
• Water is not flowing into the machine due to the water supply taps being closed.
• The timer is faulty. In this case, the washing mode of the selected program does not start due to a broken time relay. To check, turn the program switch until the drum begins to rotate. If this happens, it means that the timer is faulty and requires replacement.

Washing machine drum does not fill with water

First of all, check whether the water supply taps are open. Next, make sure that the inlet hose is not deformed or clogged. Rinse it if necessary.

If the inlet filter is clogged, perform the following manipulations:

• Close the water supply tap.
• Disconnect the hose from the unit inlet valve.
• Remove the filter and rinse thoroughly under running water.
• Install the valve, connect the hose and open the water supply valve.

If the intake valve breaks, it will need to be replaced. You can also do this yourself. It is necessary to remove the valve from the inlet pipes and replace it with a new one.

The water intake system is a weak point in Atlant machines. In good condition, when the water level in the drum rises, the water compresses the air in the pressure regulator compartment. When the pressure reaches the required value, the switch operates and the inlet valve closes. At the same time, power is supplied to the heating element and the switch for prohibiting premature opening of the drum door is activated. If the tube is damaged or clogged, the water supply system will not work.

To troubleshoot:

• Check how the tube is installed on the water level switch. If the end of the tube has hardened, cut it a couple of centimeters and put it back on the switch.
• To check that the switch is working properly, blow into the tube. The click of the switch should be heard.
• Afterwards, loosen the clamp on the hose that secures the pressure chamber to the drum.
• Flush the chamber so that the inlet and outlet ports are clean and free of blockages. Inspect the camera for cracks and deformations.
• Make sure the switch is working properly: test it with a multimeter. If damaged, replace with a new one.

Washing machine drum fills with water too slowly

Standard reasons why water fills slowly into the washing machine:

• The inlet hose is clogged or deformed. In this case, rinse the hose under water pressure.
• The inlet filter is clogged. Remove and wash the filter.
• The water pressure in the system is not high enough. Make sure the water supply valve is fully open.If yes, then there is insufficient water pressure in the line. It needs to be raised. For example, install a pressure tank under the ceiling of an apartment, or in the attic of a house. The minimum required pressure is 12 atm.

The water in the washing machine does not heat up. Heating element failure

Causes of breakdowns and options for eliminating them:

• The water level regulator is faulty. A faulty water level switch does not recognize that the drum is full, so it does not turn on the heating element. Check the switch with a multimeter and, if faulty, replace it with a new one.
• Scale has formed on the heater. Due to increased water hardness, limescale appears on the heating element, which affects the operation of the heater. Disassemble the washing machine and descale it.
• Malfunction of heating equipment. The heater contacts need to be tightened and oxidation removed. Using a multimeter, check the heating element for an open circuit by first disconnecting one wire from the heater. If necessary, replace it with a new one.
• Thermal relay failure. It is used to measure the temperature of the water in the washing machine tank and turn off the heating element when the desired temperature is reached. A malfunctioning thermal relay turns off the heating element incorrectly: too early or too late.

Automatic stopping of the washing machine during a cycle

If the washing machine stops on its own during an incomplete wash cycle, check the presence of power in the outlet using a multimeter. If everything is fine with the power supply, the reason for the shutdown may be a clogged inlet or outlet hose. To remove the blockage, rinse the hose under the tap.

The next step is to remove and check the serviceability of the pump.It may be clogged or broken.

Next, check the serviceability and cleanliness of the intake valve. If necessary, replace with a new one. Next, check the operation of the thermostat, heating element and timer. If the timer malfunctions, replace it with a new one, as repairs are too difficult for a non-specialist.

A typical case when repairing an Atlant washing machine is the failure of the electric motor. The “weak link” in it is the brushes. Such repairs require special skills and it is better for the user to contact a service center. The good news is that in most cases the engines can be repaired and there is no need to buy a new one.

The drum does not rotate

First, rule out the simplest reason - a broken door latch. If the lock is faulty, the drum will not rotate. To check, press the door button several times, it may be stuck.

If the drum in the washing machine is not mounted on a direct drive to the motor, but on a tension belt, the belt may come off. Move the engine down a little and adjust the belt tension tighter. Be careful not to overdo it. Too much belt tension will cause rapid bearing wear and failure. With the correct belt tension, when pressed, the belt moves about 12 mm. If your washing machine does not have a belt tensioner, the best alternative is to replace the belt with a new one.

Another possible reason for the drum stopping is a breakdown of the electric motor. In this case, you should contact a specialist.

Problems with draining water

The first possible reason for water retention in the drum is a clogged outlet hose or its deformation. Check the hose for blockages and flush if necessary.The exhaust filter may also be clogged. You can clean and replace it through the hole located at the bottom of the washing machine.

The next possible reason is a clogged pump. Remove it and check for foreign objects. To do this you should:

• Prepare a rag for water in advance.
• Remove the clamps securing the hoses to the pump. Check the hose for blockages.
• Using a pencil, check the rotation of the impeller. If the impeller rotates slowly, remove the chip with wires and mounting bolts from the pump. Then remove the clamps or screws that connect the two parts of the pump.
• Mark or take a photo with your phone of their location so as not to confuse them when assembling. Check the impeller chamber for debris, and also make sure there are no threads wrapped around the shaft.
• Clean and reassemble the pump. If the above manipulations did not help, replace the pump with a new one.

 

Loud or unusual noise during wash or spin cycle

If your washing machine suddenly starts making loud noises or clanking noises during the wash cycle, you may have left coins, keys, or other foreign objects in your clothing pockets. If small metal objects from the drum fall into the tub, the washing machine may be seriously damaged. Therefore, it is important to check pockets before washing.

Another reason for unusual sounds may be a broken latch or door lock. The sound in this case will be buzzing and will stop when the door is closed.

If a squealing sound appears when washing at high speeds, this indicates that the drive belt is slipping. Tighten the belt or replace it with a new one

If you hear a rattling noise when the drum rotates, the drum bearing is broken and needs to be replaced.

Strong vibration, spontaneous movement of the washing machine on the floor

If a similar problem occurs for the first time, the reason lies in an overloaded drum of the unit or in clothes unevenly distributed in the drum. Remove excess clothing from the drum and continue to follow the recommendations of the Atlant washing machine manufacturer.

If the unit vibrates more than once, while moving along the floor, it means that the washing machine was installed incorrectly, not level. Re-align the unit by adjusting the height of each leg.

Washing machine door won't open

The most common reason for the door blocking is water remaining in the tank after washing. Drain the water from the drum using the drain mode. Check for blockages in the drain pipes and whether the pump is working correctly.

We shared with you the most common causes of breakdowns of Atlant washing machines and gave fairly detailed instructions for eliminating them. Follow the manufacturer's recommended operating rules, and your assistant will serve you longer.

Rules that will help extend the life of your washing machine:

• Before loading items, check pockets for coins, keys, and other items and debris.
• Clean the heating element regularly to remove scale.
• Use hard water softeners and a cleaning filter.
• Regularly clean the drain filter of debris and dirt.
• Wipe the powder and additive drawer dry after each wash to prevent mold from forming.