Among washing machines, Electrolux is one of the most popular brands. It is of good quality, and you should expect the best results from such a washing machine. However, sooner or later, every washing machine may have breakdowns and malfunctions, and this is quite normal. Then a person can contact a specialist. And it happens that he repairs the Electrolux washing machine himself.
Making repairs yourself is not so difficult, it’s like replacing a faucet in the kitchen. When there is a malfunction in the dial or the door breaks, something needs to be done urgently. Many people call a professional without figuring out the problem themselves. First, you need to look and make sure that you won’t be able to carry out the repairs alone. Only then can you invite a professional in this matter.
Causes of breakdown and repair
Electrolux washing machines are able to decipher errors that appear on the display. Let's say that if the gasket wears out, then it will not be possible to understand until a leak occurs.
If you notice that the Electrolux washing machine is not working properly, then you need to find the cause of the breakdown and fix it. If there is even a small problem, it can lead to bad consequences.
The malfunction is displayed on the display of the Electrolux washing machine in the form of the following codes:
- E11, EC1, EF4 – incorrect operation of the filling valves or their blocking. Perhaps something is preventing water from pouring inside, there may also be a little pressure. Electrical wiring fault or damage to the flow sensor. E13 rupture of various hoses or violation of the integrity of the units through which water flows.
- E21, EF1 the hose from which the drain is being drained is clogged, or the electronic controller is not working properly.
- E23 some part burned out.
- E24 breakdown on ED.
- E85 malfunction of the unit or pump; it must be replaced or repaired.
- EF2 a large amount of poured powder.
- EF3 There is a water leak somewhere, or there is no current supply to the drain pump.
Such errors can also occur in other washing machines. But it may take a lot of time to solve the problem and make a diagnosis. It is important to have good nerves, as well as knowledge and experience. Repairing Electrolux washing machines is not so easy to do. Therefore, if a person is not confident in himself and his abilities, it is better to call a good master.
Electrolux washing machine does not turn on
The most common reason in this case is a lack of electricity. There are various reasons, most often the machine is knocked out due to a short circuit. In some cases, a protective shutdown is triggered. Most often this happens due to bad wiring. There may be no power if the outlet is faulty.
It also happens that the cause of breakdown of the Electrolux machine is the surge protector. You should check your washing machine and connect it directly to the outlet. It is possible that the cord itself cannot withstand constant load. If a wire break is found, you must immediately replace it with a new one, since there is no point in repairing it. It happens that the power button breaks, because in some Electrolux washing machines it is where the power goes.
Before checking, the Electrolux washing machine must be unplugged from the outlet. The operation of the button can be checked with a multimeter in buzzer mode. There may also be a breakdown due to the interference filter. To check it, you need to make a call. The most dangerous reason why the Electrolux washing machine does not turn on is a malfunction of the control module. After all, during the repair of the washing mashine, it may be necessary to replace it, which will require a lot of money. Of course, you can make such repairs yourself, but you may not be able to do it, and there will be a risk of breaking it.
To repair the power button, you need to remove the powder receptacle. There will be a fastener inside on the right; you need to unscrew it. You will also need to unscrew the retaining panel. You should also unscrew all the bolts and remove the panel. If the cause is found in the contacts, you should solder them and clean them.
The cause of the failure is probably the network cable. It often happens that the wires become loose and the power to the washing machine fails. Perhaps there is no power supply or it is supplied, but intermittently. This is very dangerous and may cause a short circuit. If a breakdown is detected, then you need to look at the power cord and filter.First, you will need to remove the cover of the Electrolux machine; there is a protective gasket next to the cord; you need to disconnect it. You should carefully inspect the contacts and wires, if they are securely fastened, disconnect them and check them with a multimeter. If the cable is damaged, then replace it with the original power cord.
Most often, what happens is that the Electrolux machine turns on, but when you start the wash, the machine is knocked out and shuts down. In this case, you should seek help from a good electrician as soon as possible. The socket may be faulty or the wiring may not be able to withstand the heavy load. Therefore, if such a breakdown occurs, it is prohibited to use the washing machine, as this can lead to bad consequences.
Water does not heat up
Modern washing machines do not depend on what kind of water is in the water supply. Washing equipment has the ability to heat water itself to a certain temperature. It becomes not very pleasant when the water in the Electrolux washing machine does not heat up. You can find the cause of the breakdown in about twenty minutes. You just need to put your hand on the glass. If it is cold, this means that the water is not heating.
Most often, the reason is that the installation and connection of the Electrolux washing machine was performed incorrectly. It is also possible that the wrong washing mode is set, since not all programs can heat the water very much, and therefore the heat is not felt when you touch the hatch cover. It is also possible that the water heater may break down, after which the washing machine does not heat the liquid. The cause is most often scale, which leads to overheating, and eventually the heating element burns out.Sometimes a malfunction occurs due to voltage fluctuations. It also happens that the temperature sensor fails, and the machine automatically stops heating the water so that the heating element does not overheat.
It is quite difficult to confuse a heating element failure with another. Making a replacement yourself is not as difficult as it seems. The most important thing is to do washing mashine repairs carefully and efficiently. Before repairing the heating element, you must first check it using a multimeter. There may be a breakdown in it entirely, or in the control board, but this happens extremely rarely. It is still worth noting that you can repair Electrolux washing machines yourself, the main thing is to have good patience and a little experience in this.
The RCD is triggered when the washing machine is turned on
As a rule, an Electrolux washing machine is installed in the bathroom, so it is necessary to have protection against current leakage. A differential automatic machine is installed separately. It is also possible to install a residual current device. It happens that protection works without any obvious reason.
Often it works due to incorrect connection of the differential machine. It is also possible that the device has failed and its operation should be checked. To do this, you need to disconnect all the wires, and when the RCD is turned on, you need to press the start button. The protection should turn off, and if this did not happen, it means that the residual current device needs to be replaced with a new one. If no damage was found, then it is worth inspecting the washing machine. Often a malfunction occurs in older units, as they have damaged wiring. The parts inside may become deformed and may cause current leakage.
Perhaps the reason is faulty electrical wiring, if it was damaged by a self-tapping screw. It also happens that moisture gets into the shield. If no damage is found, it is necessary to completely replace the wiring.
Water does not fill the tank and the system does not drain
If water is not being filled into the tank of the Electrolux machine, there is no need to panic and call the technician right away. You need to try to find the cause and repair it yourself. First you need to understand whether the water supply is working properly. It happens that water flows intermittently due to low pressure.
There are times when a person forgot to open the tap that supplies liquid to the Electrolux washing machine. If no fault was found in the water supply, then the reason may be in the Electrolux washing machine. If low-quality water comes in, this happens due to a clogged inlet valve. It can also burn out if there are power outages. If the failure is in the heating element, then the wash does not start.
If the reason is that the water is not draining, it may be a clogged drain filter or drain. You can do this type of repair yourself. To eliminate this, you will have to completely clean these elements. Such methods are preventive measures and are most often carried out by the owner of the equipment. If no blockage is found, then you need to inspect the drain pump or pump. If a problem is found, the devices are replaced. It happens that the pressure switch stops working. This is a sensor that is responsible for the water level.
Electrolux washing machine creates noise and vibration
Malfunctions of Electrolux washing machines often lead to noise and vibration.Some washing machines may vibrate strongly when the laundry is spinning. There may be an uneven surface where it stands. This is why vibration occurs during washing. To eliminate the cause, you need to buy a stand for the washing mashine or make it yourself. There may also be a coin or button stuck between the tub and the drum. When something gets inside, you can hear a creak. In this case, repairs will be very simple.
You will need to remove the debris from the machine and conduct a visual inspection. The drum mounts may have become loose. Then a crackling and whistling sound begins to appear. To correct the problem, you will need to reseal the fasteners. The shock absorber and bearing may also wear out. The machine begins to shake when washing, and parts will need to be replaced during repairs.
Electrolux models are equipped with a counterweight to eliminate noise and vibration. Over time, it can crumble or completely weaken. This element ceases to perform its functions and can cause unpleasant sounds.
Rinsing does not occur and powder remains
About five years after the start of operation, Electrolux washing machines begin to experience the first problems with washing. It often happens that the detergent remains in the tray. It turns out that the clothes are washed without powder. When the Electrolux machine takes in water, it should flow through the cuvette where the powder mass is located.
There is a valve near the compartment where the detergent is located. It opens and washes everything out with water. It is possible that the valve itself is not suitable for operation. Maybe it's clogged with dirt and that's why it won't open. First you need to pull out the compartment where the powder is located.Also remove the top cover of the Electrolux machine and find the valve and check its condition. If it is already completely worn out, you need to purchase a new one.
It happens that the Electrolux washing machine does not rinse or spin, even when a special mode is set. This may be a sign that the control module has failed. It is difficult to carry out such repairs yourself if you do not have any skills in this matter. Then you should seek help from a professional.
Breakage of the rubber seal and drum of the Electrolux machine
If severe vibration occurs and the Electrolux machine becomes disturbed, this can lead to serious consequences. The vibration is so strong that the washing machine may even fall. Also in great danger are water pipes, furniture, and parquet. The problem may be that the installation was not performed correctly. Also, an uneven floor can cause strong vibration. Or it could be that the drum bearing has become faulty.
You can repair an Electrolux washing mashine yourself, as there is nothing complicated. It is necessary to remove the old seal and install a new one in its place. It is secured with latches. It's easy to see how to install it. As a rule, the instructions contain all the necessary information to replace the seal. Almost anyone can cope with this problem. But, if you have any doubts that you won’t be able to carry out the repairs yourself, you should contact a professional. Making repairs is not as difficult as it seems. When a breakdown occurs, an error code is displayed. Using the instructions, you can find out what the reason is.
Prevention
In order for the Electrolux washing machine to serve you for a long time, you need to take careful care.The rubber seal must be wiped after each wash. There is an accumulation of moisture, hair, and animal fur. If such procedures are not carried out, an unpleasant odor may appear in the drum itself. It is also necessary to clean the pump filter regularly. Small objects often get caught in it, and this leads to poor drainage.
Scale often forms and this has a bad effect on washing. Therefore, it is necessary to try to add a special anti-scale powder with each wash. You should also always check your pockets for items before washing. Always wash your bra in a bag. You should use a special powder designed for an automatic washing machine.
To avoid problems, you should handle the Electrolux machine with care. And if a breakdown occurs, you should try to find it yourself and, if possible, repair or replace the faulty part. But, if you suddenly don’t have enough strength or patience, it’s best to use the services of a specialist.
