Modern Atlant washing machines have a built-in self-diagnosis system. If any malfunction is detected, the equipment displays a message with a numerical-alphabetic code. To decipher it and determine the type of failure, you need to refer to the user manual, which lists all the error codes for Atlant washing machines.
Decoding error codes for Atlant washing machines
When deciphering the data displayed on the screen of the Atlant washing machine, it is worth understanding that the self-diagnosis system does not check a specific part, but the entire link to which it belongs. So, for example, if a technician displays a message about a pump malfunction, this does not mean that this particular element is broken. The problem may be clogged hoses, broken pressure switch, broken contacts, etc.
Some Atlant washing machines do not have a display. In this case, the equipment reports a malfunction by flashing LEDs on the control panel.
Depending on the breakdown, the following SMA Atlant error codes may appear on the Atlant equipment display:
Door
Door or flashing 1, 3 and 4 LEDs. This message indicates that the washing machine door is not closed tightly.The cause of the breakdown may be a malfunction of the locking lock, damaged wiring from the UBL to the central board, broken contacts, incorrect installation of the Atlant washing machine, skewed hinges, a defective latch or guide. To fix the problem, you need to make sure that the device is installed correctly, level and on a flat surface. Next, you should tighten the door hinges, use a multimeter to diagnose the UBL and wiring, and also inspect the handle. Damaged parts must be replaced.
Sel
If the message “Sel” appears on the display or absolutely all indicators go out, this means that problems have arisen in the control panel. Parts may be worn out due to long-term use, and the buttons may be pressed or stuck due to the ingress of detergents and stop responding to pressing. It is necessary to check the serviceability of the buttons and program switch; if everything is in order with them, you need to diagnose the control board.
None
If “None” appears on the screen or all indicators light up at once, this indicates an excess of foam in the tank. The problem may be the wrong choice or a large amount of detergent, as well as an incorrectly set mode. It is necessary to choose a powder for automatic washing machines, add it in smaller quantities, and also use other washing programs.
F2
This message or the blinking of the third indicator indicates that the temperature sensor is not functioning. Perhaps the device itself is broken, the integrity of the contacts or wiring is damaged, or the control unit is faulty. It is necessary to check and, if necessary, install a new sensor, inspect and repair contacts and wiring, or diagnose the control board.
F3
Flashing of the third and fourth indicators or error code F3 indicates a breakdown of the heating element. Possible broken contacts, malfunction of the heating element, thermistor, or significant scale deposits on the heating element. It is necessary to check and ring the heating element and contacts, diagnose the thermistor, and remove scale from the heating element. Damaged parts should be replaced.
F4
Error code F4 or the blinking of the second indicator indicate that water is not draining or is draining very slowly. This indicates a blockage in the drain system or problems with the pump. You need to inspect and remove dirt and debris from the drain filter, hose, and pump. Next, you need to ring the pump and its contacts, check for damage and replace if necessary.
F5
The appearance of error code F5 on the machine screen or the blinking of the second and fourth LEDs indicate problems with the water fill hose. This symptom indicates a blockage in the water inlet system or a broken inlet valve. It is necessary to remove debris in the inlet hose, inspect the filter mesh installed behind it, and clean the valve hoses. Next, you need to diagnose the valve and change it if necessary.
F6
Error F6 or blinking of the second and third indicators indicates a malfunction in the operation of the reverse relay. Possible problems: the relay does not work or the contacts are damaged, the motor of the Atlant washing machine is faulty. To eliminate the breakdown, you need to check all components and replace the broken one.
F7
Error F7 on the machine screen or flashing second, third and fourth indicators indicate problems with the electrical network. This indicates a voltage problem or a faulty noise filter.The faulty unit must be replaced, if there are problems with the electrical network, call an electrician to fix them.
F8
Error F8 and the blinking of the first indicator indicate that there is a large amount of liquid left in the tank. The cause of the malfunction may be a broken pressure switch, control board, or jammed water inlet valve. It is necessary to inspect the water level sensor, run diagnostics, blow out the tubes. If the valve is jammed, replace the part. In case of problems with the control unit, you need to install a new one.
F9
The blinking first and fourth indicators or error code F9 on the machine screen notify that the engine speed sensor is broken. There may also be a malfunction in the motor itself or a problem with the wiring or contacts. It is necessary to diagnose the units, replace the damaged ones. You should also ring the contacts, check the wires and restore them if problems are detected.
F10
Error F10 and the blinking first and third LEDs indicate that the electronic door lock is faulty. The Atlant washing machine will not work until the hatch is locked. To fix the problem, you need to check the UBL and contacts and replace the broken element.
F12
The F12 code or the first to third indicators flashing indicate a malfunction of the Atlant washing machine motor. The motor itself or the burnt-out control triac on the central board may be faulty. It is necessary to repair the motor and perform diagnostics of the control unit and subsequent restoration.
F13
This code or the flashing of the first, second and fourth LEDs indicate a breakdown of the control board or damage to its circuits. This can happen in the event of liquid ingress or a short circuit.It is necessary to inspect and repair the faulty part or restore the chain links.
F14
The first and second indicators or error code F14 on the machine screen indicate a software failure. It is necessary to replace the control module or perform flashing.
F15
This code notifies that a leak has been detected in the Atlant washing machine. This can happen due to wear of the cuff, leakage of the hoses at the joints, or leakage of the tank. It is necessary to find the problem area and fix the damage.
Conclusion
Modern Atlant washing machines use a self-diagnosis system to find a malfunction and notify the user about it by flashing LEDs or displaying an error code on the screen. By deciphering such a message, the owner of the device will be able to understand whether he is able to fix the problem on his own or whether it is better to turn to professionals for repair work.
