The error codes of Indesit washing machines are very similar to the codes issued by Ariston washing machines, since there is only one brand manufacturer. Therefore, if you have previously encountered Ariston, then understanding the identification principle is much easier. All information on Indesit error codes can be found in the instructions for use, which are necessarily included with purchase.
How to identify the problem?
There are two ways to determine the specifics of the error that the Indesit washing machine produces:
- by code displayed on the electronic display;
- by blinking (for a washing machine of an older model, which does not have a display) of buttons.
The first option is relevant for washing machines produced after 2000: they are distinguished by more sophisticated electronics and an improved self-identification system for faults.
What Indesit error codes exist and what should I do?
The main errors issued by Indesit have values from F01 to F18, as well as H2O. However, there are exceptions to consider:
- F16 is typical exclusively for top-loading washing machines;
- F13-15 are not available on Indesit machines that do not have a drying function.
When a breakdown occurs, the code of which is displayed on the display or recognized by the number of blinks, the door is blocked.Indesit error codes can signal both technical problems and incorrect inputs (exceeding the permissible load limit, for example). The Indesit washing machine can generate an error both at startup and during operation (when switching to rinsing or spinning, if a functional discrepancy is detected).
F01
The error indicates a malfunction of the electric motor, possibly a short circuit in the circuits.
What's coming?
- Checking the engine electrical circuit.
- Replacement of the control semistor if it burns out.
- Repair or replacement of the control board.
A washing machine without a display will indicate a malfunction with a flashing light on button 4.
F02
The error indicates a breakdown of the tachometer or a break in the contacts between it and the module.
What to do if the washing machine behaves like this?
- Checking the tachogenerator contacts.
- Checking the control module.
- Possibly replacing the tachogenerator.
A washing machine without a display will flash. 3.
F03
Code F03 “Indesit” will show if the thermistor fails or the relay gets stuck.
What to do?
- It is necessary to diagnose the sensor, check the resistance (if necessary, change the part);
- Inspection of relay contacts, restoration of burnt ones.
An older model washing machine will flash buttons 3 and 4.
F04
Code F04 indicates that the pressure switch readings are incorrect. The water may be turned off, the shut-off valve is not open, there are blockages in the inlet filter, or the pressure switch is broken.
What is the right thing to do?
- Check the water, open the shut-off valve.
- Remove the blockage in the filter.
- Inspect the pressure switch, clean the tubes, and if it is seriously damaged, replace it.
If the washing machine is an old model, the error will be reflected by blinking button 2.
F05
Does the Indesit washing machine show code F05? Problems with the drain pump! There may be several reasons:
- broken pump, interruptions in wiring;
- the drain system is clogged;
- The pressure switch is broken.
What will you need?
- diagnostics, restoration of damaged wiring sections.
- eliminating blockages in the pump or filter located behind the hatch.
- It wouldn't hurt to inspect the pump impeller.
- in a critical situation, a new pressure switch will be needed.
“Indesit” without a display in the event of such a breakdown shows the book. 2.4.
F06
The error is due to problems in the control system. There may be three reasons:
- The controller controlling the panel has failed;
- the contacts between the board and the controller are broken;
- The main module is inoperative.
What to do?
- First of all, you need to diagnose in which of the listed sectors the failure occurred.
- Repair or replacement of unsuitable parts.
The error on the buttons will be indicated by flashing 2,3.
F07
The water does not heat up. Perhaps the heater relay is stuck or its contacts have burnt out. In the worst case, the heating element has burned out or the pressure switch has become unusable.
What to do in this situation?
- It is necessary to check the heating element and pressure switch, and if necessary, replace them.
- Checking the adjustment of the pressure switch connections.
Error in the language of the model without a display - buttons 2, 3, 4 blinking.
F08
Corresponds to a stuck heater relay or board malfunction.
Need to produce:
- checking the relay (most likely, you will need to install a new part);
- research and “reflashing” of the control module.
If there is no display, 1 will flash.
F09
Code F09 indicates problems with RAM. It is necessary to diagnose the electronic controller - “reflash” or replace the board.
By the blinking of the buttons, this malfunction can be recognized by the combination of flashing 1 and 4.
F10
The pressure switch stopped giving signals. There may be several reasons for this error:
- no water is supplied, the water supply valve is closed;
- blockages in the drain system;
- The water sensor level is acting up.
You can also repair it yourself:
- just check the water supply or open the valve;
- clean the drain system, inspect the intake valve;
- The sensor may be broken and will have to be replaced.
An old-style washing machine will blink with buttons 1 and 3.
F11
The error is due to either problems starting the pump (clogged filter, pump impeller) or lack of drainage (pump malfunction).
What to do?
- Clear the filter of blockages; if the impeller does not rotate, you will have to clean the pump.
- Check the pump winding resistance: if it is not normal, the pump should be replaced.
“Indesit” of the old model will signal this by blinking the combination of buttons 2, 3, 4.
F12
It is difficult not to pay attention to this error - the indicators will not light up when you press the buttons. This is caused by burnout of contacts between blocks.
What to do?
- Diagnostics of the controller, control module.
- Restoring burnt out contacts.
A machine without a display will flash buttons 1, 2.
F13
The drying sensor is acting up: the contacts are faulty or the sensor itself is broken. Contacts should be checked and damaged ones restored. In the worst case, you will need to change the drying temperature sensor.
1, 2, 4 – a combination of flashing buttons on Indesit without a display.
F14
The heating element, which is responsible for drying clothes, is acting up. There are several reasons: the heating element burned out, there was a risk of overheating and the heating element was turned off, all the water did not drain from the drum.
Options to solve the problem:
- changing the heating element;
- Thanks to the “drain” function, remove any remaining water from the drum;
- if the contacts leading from the board to the heating element are damaged, restore them.
You can also recognize it by blinking buttons 1, 2, 3.
F15
The drying relay is stuck. The problem may be due to a broken control board, loose contacts, or a malfunction of the relay system itself. It is worth “correcting” the wiring leading from the heating element to the control board. Did not help? It is necessary to examine the module, which is best entrusted to a specialist.
A flashing combination of 1, 2, 3, 4 indicates a similar problem.
F17
The door is not closed tightly. Perhaps it was not pressed tightly, or perhaps the electronic lock was acting up or the wiring was coming loose (it should be checked first).
An error on the less advanced “Indesit” will be reflected in the blinking LED 4 - book. 4.
F18
The code indicates that the controller is not working properly. This may result in repair or complete replacement of the electronic module.
By blinking, the breakdown is identified by LED 4 – book. 3.
H2O
The code indicates a blockage in the drain system sector or the washing machine is not connected correctly. There are two options to solve the problem: cleaning the drain system or reconnecting the machine.
Thanks to the achievements of modern electronics, using the display provided by the Indesit washing machine, you can accurately determine the cause of a technical malfunction or inconsistency of input data. If the Indesit washing machine displays an error related to a malfunction of the control module, it is better to entrust the diagnostics and repairs to a specialist so as not to aggravate the situation.
