This error is often displayed at the initial stage, sometimes at the end, and very rarely during the operation of the washing machine. The unit does not start washing, the program is interrupted, and the door may not open. And all these negative phenomena are accompanied by a corresponding signal - Door error in washing machines.
How is the signal decrypted?
By the way, on some washing machines it may display the alphanumeric code F 16. The problem means that an error was made when closing the door. For some reason, the hatch is not locked, or the unit’s electronics do not “recognize” the action performed.
Deciphering the problem indicates a probable breakdown of the device blocking the hatch. But we should not rush to conclusions. It is likely that there is no breakdown, and everything that happens is a consequence of a program failure or your personal carelessness.
We fix the problem ourselves
There are several generally accepted rules that will help cope with the problem. They are used in certain situations:
- The hatch did not close tightly - you need to check, most likely, when closing you did not apply the necessary force, or something got between the door and the rubber seal that is preventing it from closing. We recommend performing the action again; you should hear a characteristic click.
- The network voltage has dropped - check. If there is no 200 volts in the network, the hatch lock does not work. But the problem can be solved - a relay is installed that controls the voltage.
- The hole for the door tongue in the lock is clogged - make sure everything is in order.
- The hinge fasteners of the door have become loose - as a result, the tongue does not always fit into the lock, and the hatch may not close. You'll have to tighten the fastenings.
- A failure of the control or display unit has occurred - when the error appears for the first time, simply unplug the machine from the socket, pause for ten minutes, and turn on the device again. The unit will reboot, it is quite possible that the error will disappear.
- Poor contact - it is necessary to check the area from the hatch blocker to the block responsible for general control. It happens that the vibration of the SM during operation is the reason that the contact connections have “moved away”.
If your actions are unsuccessful, it means that the machine is seriously damaged and needs professional repair.
Door error in washing machines of various companies
Let's consider more specific actions for SM from leading manufacturers.
Indesit
You can often hear complaints about models from this company that they often break down. We will not argue about the quality of the product, but will deal with the door error code - as the most common problem.
The peculiarity is that the lock located inside the door is thought out rather poorly. The axis holding the hook with the spring pops out from time to time. As a result, the hook cannot lock the hatch in the “closed” position. If this happens, don’t get angry and kick the door. Just follow a few simple steps:
- disconnect the machine from the electrical network;
- remove the water in the washing machine using a garbage filter;
- unscrew the fasteners and remove the door;
- unscrew the screws that secure the parts of the hatch together;
- insert the axle into the place intended for it;
- We perform assembly in reverse order.
If everything is fine with the mechanism, but the hatch does not close, you should check the hatch control unit, module, etc.
Atlant
Such machines not only have mechanical latches, but are also blocked by an electronic device. It works from impulses - the plates in the device expand, pressing the lever. Sometimes they wear out and the device needs to be replaced. But first, it is recommended to check using a multimeter.
We also inspect the lock opening and remove any debris that has accumulated there. We check the wiring connecting the lock blocker and the control unit. It is likely that the problem lies here.
The final stage is checking the module for board resistance. It may need to be repaired or replaced completely.
There are also other mechanical problems. To eliminate them, we check certain places:
- We inspect the position of the hinges - the hatch could be warped due to poor installation or long-term use. In these cases, the latch will not reach the lock. We check the evenness of the installation, tighten the hinges to return the door to its normal position;
- we check the handle - if the element is broken, you should remove the door and replace the element;
- latch - it can move due to the fact that the pin holding it falls out. To fix the problem, the lock mechanism will have to be disassembled;
- The plastic guide element is worn out - when the characteristic click of the lock is not heard, the guide should be replaced.
Ariston
It should be noted here that actions with Atlant and Indesit are also relevant for this brand. But they still have their own characteristics. In an Ariston machine, this signal has nothing to do with the door lock. A similar error can occur from poor contacts on the motor brushes.
In this case, you should get to the motor, unscrew its fastenings, and disconnect the wiring connector. Having removed the motor, we check the integrity of the brushes and inspect the wires that power them. It is possible that the brushes are worn out from prolonged use and need to be replaced.
Samsung
On washing machines from this company, not only this error signals problematic issues with the door. Signals de, Ed, de 1, de 2 may appear.
Problems are associated with the following features:
- the hatch is not blocked from the very beginning;
- the door does not open after finishing the wash;
- First the blocking works, then it disappears. The machine “freezes” and produces a corresponding signal;
- the door tongue did not hit the lock;
- The signal may appear and disappear many times during the wash cycle, from five to seven times.
What should be done in such cases? Let's look at the simplest option, when the hatch closed and a click was heard, but the machine signaled a problem. In this case, it is necessary to check and, if necessary, repair the blocking device.
And if the door does not open after the washing process, the problem should also be looked for in this place. But first it is recommended to wait ten minutes. The lock may open automatically.
The error may also be due to mechanical problems.If the hook simply does not get into the lock, you should make sure that the hinges holding the hatch are properly fastened. They become loose quite often and need to be completely replaced. By the way, it is best to install a new “reinforced” analogue made of a special alloy. We guarantee that such problems will not happen again.
It’s bad if the signal appears and disappears on its own. The problem will have to be found in the contact group or wiring, and this is a task for an experienced technician.
Conclusion
It would not be superfluous to repeat that the problem with closing the hatch on washing mashines from different companies manifests itself with its own signals. The actions, as a rule, are the same in all cases, but sometimes the reasons for refusal can be the most unexpected.
