Washing machines from any manufacturer, including LG, break down over time. Very often, during operation, the owner of the device discovers that the LG washing machine does not drain water and does not spin clothes. This malfunction occurs for a number of reasons, most of which can be eliminated on your own without the help of professionals.
How to drain water if the washing machine won't drain
If the LG washing machine does not drain, you must stop all programs and do this work yourself. This can be easily done by removing the drain hose from the drain and lowering it into a basin located below the level of the LG washing machine. The water will flow out by gravity.
The second way to drain is to open the plinth panel on the front of the LG washing machine. There is a small hose inside for emergency drainage. You need to lower it into the container and pull out the plug. If there is no hose, you can drain the water by tilting the machine back, placing a basin and partially unscrewing the filter. It is not recommended to completely pull out the part, otherwise strong water pressure will flood the floor.
Another way to get rid of water in the tank is to turn the LG washing machine around, remove the back cover, find the drain pipe, release the clamps, disconnect it and direct it into a substitute container. If water does not flow out, this means that it is clogged, and the owner of the device immediately discovered the cause of the malfunction. You need to clean it, after which the drain system will work better, and the LG washing machine will be able to proceed to the spin stage.
Possible causes of malfunction
If the LG washing machine does not drain and therefore does not proceed to the spin cycle, the reasons may be:
- Contamination of the drain system.
- Pump fault.
- The pressure switch is clogged or broken.
- Broken wiring.
- Failure of the control unit.
To determine the breakdown, it is necessary to sequentially check all the listed components for blockages and breakdowns and, if any are found, eliminate them in order to correct the drainage problem.
Pump removal and repair
To detect a blockage, you first need to open the base panel from the bottom on the front part and unscrew the drain filter. It is necessary to substitute some kind of container, because in the process the remaining water will spill out. After removal, the part must be thoroughly cleaned of debris and dirt that has accumulated during operation of the LG washing machine. Also, during washing, coins, paper clips, bones from women's underwear, buttons and other small items get here. Most often, they are the cause of the blockage.
The next thing to do is to inspect the drain hose, make sure that it is not pinched, then disconnect it, blow it out, or, if a large accumulation of dirt is detected, clean it with a plumbing cable. Then return the hose to its original place and install it correctly.
Next, you need to inspect the place where the drain hose connects to the sewer. You should make sure that there is no blockage at this point, and if necessary, clean the siphon and pipes.
Now you need to inspect the internal components of the LG washing machine.
It is necessary to disconnect the equipment from the network, water supply and sewerage and move it to a spacious place. Further actions are as follows:
- Remove the detergent drawer.
- Turn the LG washing machine on its left side.
- Unclench the clamps and remove the drain pipe coming from the water tank.
- Remove the part, check for debris, clean and rinse.
- Disconnect the pump by unscrewing the retaining fasteners.
The pump must be disassembled into two parts and the impeller inspected. It often has hair, threads, and pieces of fabric wrapped around it. This makes it difficult for the part to rotate and leads to pump failure. If the impeller is clean and there are no foreign elements on it, you need to check the pump with a multimeter.
The measuring device must be switched to resistance testing mode and the probes must be installed on the pump contacts. If the numbers “0” or “1” appear on the display, the part should be replaced. A new drain pump must be purchased strictly in accordance with the device model; this can be done at a service center or in a specialized store. Another option is to order a sump pump online. A new part must be installed in place of the damaged one, after which you must assemble the LG washing machine, connect it to the network and communications, and check the equipment by running a test wash.
Pressostat malfunction
If the drain pump is intact and no blockages are found, you need to proceed to checking the water level sensor.To do this, you need to unscrew two screws from the back of the LG washing machine, slide it back and remove the top cover. In the right corner in the front part of the case, near the control panel, there is a round part with a sensor - a pressure switch. It can be removed very easily, you just need to unscrew the fasteners, disconnect the wiring and remove the hose. You will need to check the device for damage, inspect the hose for blockages and cracks, and also perform wiring diagnostics. If everything is fine, you should move on to the next step.
Failure of the control board
If the previous steps failed to identify a malfunction, this may indicate a breakdown of the washing machine control unit. This can happen for a number of reasons:
- Voltage drop, lightning strike.
- The control module tracks are poorly soldered.
- Water getting on board.
- Incorrect actions of the device owner, etc.
You should absolutely not try to repair the control unit yourself. This is a very complex process, during which you can permanently damage your LG washing equipment. To diagnose the board and fix the problem, it is recommended to contact a professional.
Spin problems
The lack of spin or its poor quality in LG washing machines may be due to the following malfunctions:
- Mode failure. In this case, the LG washing machine may reduce the spin speed, resulting in clothes remaining wet. To solve the problem, you should restart the program.
- Motor malfunction. If this unit is damaged, spinning will not take place. To carry out repairs, you need to check the winding and brushes.
- The tachometer is broken. The washing machine does not reach the required speed and does not provide high-quality spinning of the laundry.Usually the problem is caused by the mounting screw, it needs to be changed or unscrewed and screwed back in again.
- Spin problems may be caused by a faulty or clogged drain system. You need to check the pump, drain hose and filter.
Conclusion
If your LG washing machine won't drain or won't enter the spin stage, there's no need to call a professional right away. Most of the breakdowns, due to which the equipment does not drain the water or does not perform a spin cycle, can be eliminated on your own. To do this, you should sequentially inspect the LG washing machine in search of damaged components and, if found, decide whether you can fix them yourself or whether it is better to contact a specialist.
