Any Ariston washing machine is equipped with a drain filter that protects the pump from dirt and foreign objects. With active use, it gradually becomes clogged. This makes it difficult to drain the water and may cause pump failure. Therefore, the user is faced with the task of cleaning the filter in the Ariston washing machine. This is easy to do if you know where the required node is located and how to perform these steps correctly.
Where is the drain filter located?
To find the drain filter on Ariston front loading washing machine, you need to open the decorative panel at the bottom of the front side. On some models it can be easily removed by hand, while on others it will need to be pryed off with a flat screwdriver or other object. Sometimes the unit is closed by a small door that opens easily.
Having removed the panel, the consumer will find a drain hose, and next to it a filter cover that will need to be unscrewed for cleaning.
In a similar way, the necessary part is located in Ariston top-loading washing machines.
Preparing for cleaning
Before you start cleaning, you need to disconnect the Ariston washing machine from the network, water supply and sewerage.If access to the equipment is difficult, it will need to be moved to a place convenient for work.
Instructions for cleaning the drain filter
To clean a clogged unit, you will need to do the following:
- tilt the Ariston washing machine back a little, put rags and place a container for liquid under it;
- turning the filter cover counterclockwise, carefully turn it until water flows out;
- wait until the liquid is completely drained;
- Unscrew the assembly completely and pull it out;
- first you need to remove large debris from the part: dirt, foreign objects, pieces of fabric, threads, etc.;
- then use a hard sponge to remove the deposited plaque, and if it has formed in large quantities, you can soak the structure in a solution of citric acid;
- thoroughly rinse the drainage filter under running warm water.
After cleaning, you need to take a flashlight and inspect the seat. If debris and dirt are found, you will need to thoroughly clean it with a damp sponge or clean rag.
After cleaning is completed, you should install the filter in its original place. To do this, you need to place it evenly in the socket and carefully screw it clockwise, avoiding distortions. After this you can return Ariston washing machine to its original place, connect to the network and communications and run a test wash to check the device.
Recommendations for servicing the washing machine
The drain filter of the Ariston Margarita 2000 or other model washing machine must be cleaned at least once every two to four months. If the equipment is used daily, for example, in a family with several children, then maintenance of the device must be carried out every month.
How often you clean the drain filter is affected by the type of fabrics you wash in your machine. So, Products made from pile and wool are washed more often winter and autumn. These materials contain lint, which quickly and seriously clogs the drain filter, which means it needs to be cleaned more often.
What happens if you don't clean it?
If you do not maintain the Hotpoint Ariston washing machine and do not periodically clean the filter, the consequences can be very unpleasant.
- Firstly, an unpleasant odor appears. It comes not only from the Ariston washing machine itself, but also from the laundry that was washed in it. This happens because the accumulation of debris and dirt leads to the appearance and rapid proliferation of bacteria and microbes. As a result of their activity, dirt deposits turn sour, which leads to a stench.
- Secondly, the accumulation of dirt leads to the appearance of bacteria and mold. Having filled the Ariston washing machine, they will begin to poison the air in the bathroom or other room where the device is located. This can lead to serious illness.
- Thirdly, the operation of the drainage system is disrupted due to the formation of blockages.If you do not pay attention to such a breakdown, the part will become completely contaminated and, as a result, the Ariston washing machine will sooner or later stops draining water during and at the end of washing.
- Fourthly, the pump will break or malfunction. Debris from the drain filter can enter the pump. At best, foreign objects will stop the pump from working; at worst, they will damage the impeller or pump housing. Will require expensive repairs or completely change the unit.
If the part cannot be obtained
In some cases, it is not possible to remove a clogged unit from the body of the Ariston ARTF 1047 washing machine or another model. The reasons may be different: the handle does not turn, or the filter is stuck in the seat and cannot be removed out. Such consequences can result from neglecting the operating rules of the Ariston washing machine and lack of regular or periodic cleaning.
If the part cannot be unscrewed, this is due to a foreign object (for example, a bra wire or button) or scale formation between the seal and the thread. You can unscrew the knot using pliers. You must act with great care so as not to break the handle or the filter itself.
On different models of Ariston washing machines, you should remove the back or front panel of the case, then disconnect the wires, loosen the fixing clamps securing the drain pipe and hose to the pump volute, and then remove the pump connected to the volute. It is easier to clean the drain filter through the hole for the drain pipe.You can also unclamp the latches or unscrew the screws, disconnect the pump from the snail, and then clean the filter through the pump hole. After processing, it should unscrew easily.
The steps to clean the drain filter through the pump are quite complex, so if you are not sure that the procedure will be performed correctly, it is better to contact professionals.
If all the steps described above did not bring results and it was not possible to get the part, this means that an error was made somewhere or the Ariston washing machine has some feature. There is no need to break the device, the right solution would be to seek help from professionals.
If the drain filter leaks after cleaning
After the part has been cleaned, you will need to check the washing machine for a leak. It should be borne in mind that it may not appear immediately, but only after several washes.
There are a number of reasons why a washing machine leaks.
- The first and main reason is incorrect installation of the drain filter. It could have been screwed in loosely or crookedly. The part should be screwed in without distortions to prevent accidental shifts along the thread. In this case, the element should be tightened tightly, but very carefully. It is worth remembering that strong pressure when screwing the cap can damage the threads on the plastic part. To eliminate the leak, it is enough to unscrew and reinstall the unit in its original place, correcting the distortion and fixing it tightly.
- Secondly, the integrity of the rubber gasket, which ensures the tightness of the drain filter installation, could have been damaged.It could crack during use or become damaged due to careless removal of the part, as well as during careless cleaning using cutting tools. To eliminate such a breakdown, you will need to replace the rubber seals, if they are commercially available, or install a new drain filter.
- The third reason for filter leakage is its damage or a defective thread. This could happen if the part was removed incorrectly or if the cap was tightened too much. As a result, the contact of the drain elements becomes weaker, which is why a leak appears. To fix the breakdown, you will need to replace one or several parts at once, for example, a filter and a snail. If you are not sure that you will be able to perform all the steps correctly, you should seek help from professionals.
Conclusion
Each Hotpoint Ariston front-loading and top-loading washing machine is equipped with a drain filter. It prevents dirt and foreign objects from entering the drain system or pump and prevents parts from breaking and blockages. The drain filter must be cleaned regularly to avoid large deposits of debris that lead to problems with the drain system, unpleasant odors, and the formation of mold and mildew. Cleaning this important element is a very simple operation that does not require special skills or the involvement of professionals. At the end of the work, you need to carefully and correctly install the filter in its original place to avoid leaks or damage to the part.
