Error 6E on a Samsung washing machine is a fairly common phenomenon. The error may occur at the beginning, middle or end of the washing process. When it occurs, the equipment freezes, stops the work process, and the message “6E” is displayed on the interactive display. It is worth adding that depending on the year of manufacture of Samsung equipment, the codes may be different (EB, BE, BE1-BE3, B2, BC, BC2). What do these strange symbols mean, what problem causes them and what to do in such a situation?
Causes of malfunctions
The errors mentioned earlier are a signal that the equipment is having difficulty starting. There are three common reasons why error 6E appears:
- The thyristor type switch is broken.
- The buttons located on the control panel are out of order.
- There was a failure in the main controller of the Samsung washing machine.
Before starting repair work and eliminating error 6E, it is necessary to determine in which unit the malfunction occurred.In the case of models whose screen displays three characters, this is easier to do.
- Error BE1 indicates a breakdown of the power supply button.
- BE2 (B2, BC2) signals problems with other buttons.
- Error BE3 indicates a faulty control unit.
Solving problems without contacting a service center
It is not often possible to fix the problems that caused error 6E to appear on your own. However, it is necessary to consider the list of Samsung washing machine problems that can be solved without calling a technician.
Error 6E appears due to a software glitch
All modern models of Samsung washing machines are equipped with a large number of electronic sensors. A small malfunction may occur in the operation of each of them. Error 6E can be reset by rebooting the device. To do this, just disconnect Samsung equipment from the power supply for 10-15 minutes.
Problems with the socket connector
An uneven power supply can cause equipment malfunctions and cause error 6E to appear. This can happen in cases where the plug of the Samsung machine does not contact the socket tightly enough, as well as in situations with a heavily loaded network.
The problem is eliminated by putting the electrical system in order - replacing the socket, socket, power plug, and in some cases, repairing the wiring.
Control buttons do not work properly
Often, the cause of error 6E lies in poor contact of the buttons or sticking at the moment of pressing.
In such a situation, you need to hold down the problematic button or press it several times in a row. Loosening the fasteners on the front panel of the Samsung device may help.
Malfunctions requiring specialist intervention
Thyristor switch failure
There are common cases when after pressing the start button, the Samsung washing machine starts to spin the drum (as during spinning), but after collecting the required amount of water, it stops and displays the error code 6E on the screen. Sometimes the Samsung washing machine does the washing normally, and only during spinning about the error 6E.
Most likely, the thyristor switch has failed. This happens due to short circuits. As a result of such breakdowns, the control module of the Samsung washing machine begins to issue incorrect commands. Most often, short circuits of switches occur due to faulty sockets. Samsung electronics do not like voltage drops.
The breakdown that caused the 6E error is fixed by replacing the switch. Sometimes, it may be necessary to replace the switch relay and diodes.
Failure of the buttons on the control panel
On the Samsung washing machine, the buttons located on the control panel sometimes stop working. Main signs:
- The device does not respond to pressing the keys.
- The buttons stick and are constantly pressed.
Pressure, long-term use, and careless handling cause the buttons of the Samsung washing machine to break and error 6E to appear. If adjusting the front panel does not return the buttons to working condition, then their modular replacement is required.
- Failure of the main control board
- A malfunction of the control board can also be the cause of error 6E. The characteristic signs of failure are:
No response to pressing the power button.
Pressing a certain button results in the wrong modes being turned on.
After switching on, the engine spins up to maximum speed.There are common cases when, after pressing the start button, the Samsung machine begins to spin the drum (as during a spin cycle), but after collecting the required amount of water it stops and displays error code 6E. Sometimes a Samsung machine washes normally, and only gets error 6E during the spin cycle.
Most likely, the thyristor switch has failed. This happens due to short circuits. As a result of such breakdowns, the control module of the Samsung washing machine begins to issue incorrect commands. Most often, switch short circuits occur due to faulty sockets. Samsung electronics do not like voltage surges.
The breakdown that caused error 6E can be eliminated by replacing the switch. Sometimes, it may be necessary to replace the switch relays and diodes.
Failure of buttons on the control panel
On a Samsung machine, the buttons located on the control panel sometimes stop working. Main features:
The device does not respond to key presses.
The buttons stick and are constantly pressed.
