Washing machine Zanussi is quite reliable. However, even this sometimes needs repairs. As a rule, this occurs due to careless handling. How to repair a Zanussi washing machine with your own hands will be discussed later in the article.
Most common faults
The Zanussi washing machine will last quite a long time if you follow all the instructions in its operating instructions. And if you perform timely maintenance on the machine, it will work without failures. However, owners of Zanussi washing mashines They don’t always treat their technology this way. If used incorrectly, malfunctions may occur. Serious damage can only be repaired at a service center.
But very often fairly simple breakdowns arise that can be fixed with your own hands.
The most common malfunctions:
- The drum of the Zanussi machine does not rotate;
- The hatch does not open after the wash is completed;
- Water intake and drainage occurs simultaneously;
- There is no water flowing into the Zanussi car;
- The water in the Zanussi washing mashine does not heat up;
- Leaks.
The drum does not spin
Such a breakdown usually occurs every 4-5 years.The reason for this malfunction is the limited service life of the drive belt. The main symptom of this problem is that the engine of the Zanussi machine is running, but the drum is stationary.
In order to finally find out why doesn't the drum rotate?, you need to dismantle the rear wall of the Zanussi washing mashine. It happens that the belt simply jumps off the pulley. In this case, you must carefully install it in its place. But if the belt breaks, it is recommended to replace it with a new one.
It is also possible that the drive belt is in place, the motor is running, and the drum of the Zanussi washing machine is stationary. The belt has probably simply stretched and needs to be replaced. After replacing the belt, as a rule, the machine continues to work.
Zanussi washing mashine hatch won't open after washing
Sometimes there is such a breakdown that Zanussi washing machine hatch cannot be opened upon completion of washing. This usually occurs due to jamming of the blocker.
First of all, remove the bottom panel of the Zanussi washing machine. Then pull the cable found there towards you. After this, the washer hatch should open. Next, remove the hatch lock and check the condition of the fasteners.
If the latches are not broken, then the fault lies in the electronics. In this case, it is recommended to take the hatch lock to a service center for repairs. If the locks are broken, replace the lock with a new one.
Water is drained simultaneously with its collection
It happens that the Zanussi washing machine fills with water at the same time as it drains. There are several reasons for this malfunction. The first reason is that the drain hose was not connected correctly. It is in a lowered state. The problem will be resolved if you lift the hose of the Zanussi washing machine by 50 centimeters.
Damage to the pipe can also cause a malfunction. The main sign of this breakdown is water pouring directly from under the washer. In this case, it is enough to replace the pipe with a new one. However, the situation is much more complicated if the control unit is broken, which sends a signal to turn off the drain pump at an unnecessary moment. It is extremely difficult to repair such a block with your own hands.
When inspecting the Zanussi washing machine pipe, you should pay attention to its location relative to other elements. It should not come into contact with parts of the washing machine or other hoses.
Water does not flow into the machine
If this malfunction occurs, first check to see if there is no water in the water supply. If everything is in order here, check the hose for water passage. To do this, disconnect the hose from the Zanussi washing machine and turn on the water. If water flows through the hose, install it in its original place. If the hose does not allow water to pass through, then find the reason or simply repair it by replacing it with a new one.
The reasons described above are very banal. However, water may not flow into the Zanussi device due to a clogged filter. This malfunction is more serious and occurs quite often. To make repairs and clean the filter, you need to remove the top cover of the washer and then disconnect the fill valve. This element is located where the hose enters the housing. Next, disassemble and clean the filter.Then install all the elements in their places in reverse order.
After cleaning the filter, the washer usually works properly. However, even after this procedure, water may still not flow into the Zanussi washing machine. This means that the problem lies in the water level sensor or in the valve itself. It is necessary to check their condition. If the parts are faulty, replace them with new ones.
Water does not heat up
This type of malfunction does not occur often. To repair this breakdown, you need to have a regular tester and know how resistance measurement is performed. It is necessary to dismantle the back wall of the Zanussi washing machine and measure the resistance of the tubular electric heater (TEH).
This element is located at the bottom of the Zanussi washing machine tank. The resistance of the heating element should be 30 Ohms. In case of deviations it is recommended replace this element. If replacing the heating element did not help, then there is no point in further repairing the Zanussi washing machine with your own hands.
Fixing water leaks with your own hands
Water leakage from a Zanussi washing machine is not at all difficult to eliminate. This problem is usually caused by loose seals.
In order for Zanussi equipment to work properly again, it is necessary to make repairs by replacing the old gaskets at the hose connection points. However, it will be more difficult to eliminate a leaking sunroof seal.
First of all, remove the seal clamp. To do this, carefully pry it off with a screwdriver. Replacing the seal with a new one usually does not cause any particular difficulties.
