Replacing the drain hose in a washing machine is easy to do at home. However, if you do not have the time or ability to replace it yourself, you can contact a specialized service center. Before replacing the drain hose in the washing machine, you should first disassemble the housing.
This is typical for washing mashines of all brands. The installation itself occurs differently for some brands and this fact is important to keep in mind. Study all the stages of the instructions for disassembling and assembling the machine in as much detail as possible in advance so that it is easier and faster for you to navigate.
Replacing a hose in Siemens, Bosch machines
In the case of these brands, replacement occurs starting from the front housing. First of all, let's remove hatch cuff and a clamp from the wall of your washing machine. We take out the dispenser and unfasten the panel located near the base. Necessarily All remaining water must be drained through the filter. You need to lay a special cloth underneath it so that water can be absorbed into it. The last step is to remove the wires where the hatch blocking.
Next, you should unscrew all the existing bolts at the top and bottom of the machine. Here, in fact, the replacement of the hose is already taking place, which needs to be taken seriously.Once you have gained access to the inside, you need to unfasten the clamp from the tube and remove the hose. Then everything happens quite simply - the hose is pulled out and replaced with a new one by stretching the clamps. The main thing is to secure it well to the attachment point.
Replacement steps in Ariston, Beko, Indesit, LG, Samsung and Whirpool machines
For machines of these brands, you need to start the process from the bottom, unlike everyone else. We remove the water and disassemble the housing, as in the cases described above. Additionally, you need to remove the top part of the panel. The element to be replaced is installed in the required location. After installation, it is very important to check its strength.
Replacing the hose for vertical loading washing machines
Of course, replacing a hose for top-loading machines will differ from all of the above, since the machines themselves have their own specifics. The machines are expensive, so think twice before you make the replacement yourself.
However, in general, the process of dismantling the hose is even, to some extent, simpler than for machines with a horizontal loading type. First of all, you should remove the panel from the side of your washing mashine by unfastening it, as described below. To remove it you just need to apply a little pressure. As in previous types of machines, the old hose is detached here. Do not forget to stretch the clamp while removing it. Then immediately insert a new one.
Electrolux and Zanussi washing machines - how to replace the hose in them?
Here everything is done in approximately the same way as described above, however, the replacement must begin after you have removed the back panel of your washing machine. To make it easier, unscrew the bolts on the back wall with a screwdriver and carefully bend it. After removing the back panel, mark the place where the object is fixed. The clamp is stretched and the old hose is removed, after which a new one is immediately installed.
As you can see, in general, everything is extremely simple. The preparatory and assembly stages take more time. The installation of the hose itself does not take long. At most, you can spend almost a day on everything; for some it will be even more. Not a single washing machine is immune from breakdowns, even if it is very expensive; you need to keep in mind that any part, in particular such as a hose, can be damaged at any time.
Replacing the drain hose in a washing machine is a completely feasible thing to do at home. However, the process of replacing a drain hose is no easier than replacing a fill hose. This is no less important to remember.
Especially if the washing mashine is not used correctly. Replace the drain hose with your own hands and it will flow water like new and without problems!
Please note that if you cannot replace the hose yourself or you do not have enough time, it is better to contact a machine repair specialist. They will replace your damaged hose not only efficiently, but also quickly. They will always find an individual approach to each client.And besides, replacement will not cost you that much. Therefore, before changing the hose yourself, read all the instructions well and follow each step, otherwise there is a guarantee that you may ensure that it does not work properly.
In terms of time, the process will not take too long - depending on your time, the brand of the washing mashine and the method of reinstalling the hose. Replacing the drain hose in a washing machine at home is easy and without special skills or training!
