Atlant washing machine - error F3

One of the most important advantages of Atlant brand machines is a device for self-diagnosis. By the code symbols on the screen or the lighting of a certain sequence of indicators, the owner of the “washing machine” is able to determine which of the units has lost its functionality and what should be done to fix the breakdown. For example, error F3 in an Atlant washing machine may appear regardless of the program, and the washing process will continue.

Deciphering the meaning and reasons for the appearance of the code

This set of letters and numbers occurs when the water in the tank does not heat up. There may be several reasons for this:

• Heating element failure is one of the most common options. The heating element fails during operation or burns out due to accumulated plaque and scale;
• failure of the electrical circuit connecting the heating element and the control module;
• failure of any element on a modular device.

The procedure for performing repair work

To replace the heating element in the machine, there is no need to have special skills - even a beginner can handle such work. There are no difficulties here, you just need to purchase the original analogue. This should be done after all doubts have disappeared that this is where the problem lies.For repairs you will need a flat-head screwdriver and a nut wrench.

Step by step, all the steps look like this:

• the water supply to the machine is cut off;
• the machine is de-energized, the hoses for supplying and draining water are disconnected;
• To make it convenient to work, the machine should be turned with the back panel towards you;
• the fastening bolts are unscrewed along the entire perimeter;
• All electrical wires are disconnected from the heating element (their connection should be remembered or written down first in order to avoid mistakes at the time of connection);
• the functionality of the element is checked using a multimeter;
• After making sure that the heating element has burned out, you need to unscrew the fastening nut and press out the bolt;
• use a screwdriver to pry up the base of the heating element to remove it from the mounting socket;
• the working part is installed, the rubber seals are checked for integrity;
• Now the machine can be assembled and tested for functionality.

Once you have opened access to the heater and determined that it is in working condition, you should not rush to assemble the machine. There is an excellent opportunity to check all wiring and contacts. To do this, take a multimeter and ring each element in turn. It happens that the problem is hidden in the oxide covering the contacts. It just needs to be cleaned.

The last option for checking is the electrical module located at the bottom of the machine, most often near the rear panel. It turns out that by removing the back wall, you can immediately gain access to all problem areas - the heating element, electrical wiring, module. It is easy to get the latter out of the machine; to do this, you just disconnect the chips with the wiring.After this, the module must be tested, and such work can only be performed by an experienced specialist. He can easily identify a burnt triac, which is responsible for the performance of the heating element.

Advice from professionals and preventive measures

These recommendations should always be followed:

• Before starting any type of work, it is necessary to turn off the power to the washing machine and turn off the valve through which water is supplied.
• After finishing the work cycle, you need to wipe all the rubber seals on the door with a soft, dry cloth. When wiping the outer surface of the machine and other plastic parts, you can use a damp rag. It is prohibited to use alcohol, abrasives and other chemical compounds that can cause damage to the machine.

• The detergent container is washed periodically. To do this, you need to take it out and place it under running water, then put it back in its place.
• The filters installed in the water supply system are cleaned annually. You just need to disconnect the water intake hose, take out the filter element, clean it of debris, put everything back in place and check the connections for leaks.
• The pump filter is cleaned twice a year, all small objects accumulated there and thread residues are removed. Also, similar work is performed after woolen items have been washed. After removing the water, you need to open the lid with a sharp object, remove the hose completely, and remove the plug. Then the filter is taken out and washed, and everything returns to its place.

To avoid premature failure of the washing unit, it is recommended to install a stabilizing device.Sudden voltage drops can cause a break in the electrical circuit connecting the module and the heating element.

Another measure is to install a filter for cleaning. This measure is necessary to reduce water hardness and prevent the formation of scale.

It is necessary to use only high-quality powders and rinses.

To prevent overheating of the heating element, it is necessary to set the temperature regime slightly lower than the maximum value.