Modern models of washing machines from the Polish company Hansa are equipped with a self-diagnosis system. If a problem is detected, the equipment notifies the user with a message on the screen or flashing indicators. To understand which part requires replacement or repair, you need to open the instruction manual and decipher the error code that lights up on the display. This will allow you to decide whether the problem can be fixed on your own or whether professional help is needed.
Error codes for Hansa washing machines
Error codes displayed on the screen of Hans washing machines usually consist of Latin letters and numbers and contain information about the unit in which the breakdown occurred. To find out what the error means, you need to refer to the table of fault codes, which can be found in the user manual, on the manufacturer's official website or on the Internet.
Error codes for Hansa PC series washing machines
Hans washing machines of this series are equipped with a display. Depending on the breakdown, the following codes may appear on it.
E01
If the Hansa washing machine displays the E01 error, it means that the hatch door is not closed. The problem may be in the hatch lock device or in the wires from this module to the control unit.
E02
The machine was unable to fill with water within two minutes. There may be a blockage in the system, a breakdown of the pressure switch or the water inlet valve, as well as the control module. You need to make sure that the tap in front of the washing machine is open, the inlet hose and the inlet filter are not clogged with debris, then check the listed parts and replace them if necessary. To repair the control board, you should contact professionals.
E03
Error code E03 indicates that the equipment cannot drain. There may be blockages in the sewer, drain hose or pump, as well as a breakdown of the pressure switch or pump.
E04
Notification of excess water volume in the tank. The liquid inlet valve, pressure switch, or damaged wires may be faulty, in rare cases - a control module error. It is necessary to conduct a visual inspection and ringing of the parts.
E05
Error E05 reports that the machine was unable to fill with water. This may indicate weak water pressure in the system , a malfunction of the liquid inlet valve or pressure switch, as well as a breakdown of the control board. To fix the error, you need to make sure that the water is supplied under the required pressure, and then inspect and diagnose the listed sensors. Repair of the board should be entrusted to representatives of the service center.
E06
Error code E06 indicates that the washing machine cannot drain. There may be a blockage in the drain system, as well as a failure of the pump
, pressure switch or damage to the contacts.
E07
This error indicates that the AquaStop system has detected a water leak in the washing machine. It is necessary to check the operability of the protective system and, if it is working properly, start looking for the leak.
E08
The voltage in the network is too high or too low. You need to buy a stabilizer or wait until the situation normalizes.
E09
Excessive amount of foam. The powder is incorrectly selected or poured in a large volume. You need to stop the program, remove the laundry, remove the foam. Turn on the rinse mode.
E11 Failure of the triac responsible for the operation of the UBL..
Control unit repair required E21Error E21 indicates that the motor is jammed because the washing machine drum rotated at different speeds. The motor
or tachometer sensor may be broken. Both units are tested, and the faulty one is replaced. You also need to check the wiring from these elements to the control board.
E22
Code E22 indicates that the motor rotates arbitrarily, without receiving commands from the central module. This indicates a breakdown of the control triac.
The control unit needs to be repaired and the triac replaced.
E30
The door of the Hansa washing machine is not locked. You need to close it tighter, and if the error occurs again, you need to check the locking mechanism.
E31, E32
The contacts of the temperature sensor are damaged or there is a short circuit. You need to restore the circuit between the sensor and the control unit.
E42
After the program is completed, the door of the Hansa washing machine does not open. The lock may be broken or the control board damaged. E52
The central module is broken.Error code E06 indicates that the washing machine cannot drain. There may be a blockage in the drain system, as well as
pump failure
, pressure switch or damaged contacts. E07
This error indicates that the AquaStop system has detected a water leak in the washing machine. It is necessary to check the functionality of the protective system and, if it is working, start looking for a leak.
E08
The voltage in the network is increased or decreased. You need to buy a stabilizer or wait until the situation normalizes.
E09
E11
Failure of the triac responsible for the operation of the UBL. Required
control unit repair
E21
Error E21 tells you that the motor is stuck because the washing machine drum was spinning at different speeds. Possible
engine breakdown or tachometer. Both nodes are tested, the faulty one is replaced. You also need to check the wiring from these elements to the control board.
E22
Code E22 indicates that the motor rotates randomly without receiving commands from the central module. This indicates a breakdown of the control triac.
The control unit needs to be repaired and the triac replaced.
E30
The door of Hans's washing machine is not locked. You need to close it more tightly, and if the error occurs again, you need to check the locking mechanism.
E31, E32
